lopanime.blogg.se - Wiring a ceiling fan with light and 4 wires from ceiling

#Wiring a ceiling fan with light and 4 wires from ceiling how to#
#Wiring a ceiling fan with light and 4 wires from ceiling free#

Don't remove this coating it keeps the pipe from unscrewing. Tip: The pipe's threads have a factory-applied coating. Use a wrench to tighten the square-head locking screw on the side of the pipe.

Thread the down-rod pipe into the top of the motor.

Next, pass the wires through the hollow down-rod pipe.

With the fan on the floor, feed the wires coming from the motor through the center of the canopy.

Tip : If you're going to paint the medallion, do it before installing the ceiling plate.

Attach the ceiling plate to the box with two 1 1/2-inch-long 10-32 machine screws.

Hold the fan's metal ceiling plate up to the pancake box and pull the wires through its center hole.

Set the nailheads and fill with caulk or spackle.

Fasten it with four 6d finishing nails driven into the joist.

Center the medallion on the pancake box and press.

Pass the wires through the medallion (above).

Apply a small bead of urethane-based adhesive to the back of the ceiling medallion.

Wrap the cable's bare copper wire around the grounding screw inside the box.

Drive in the screws with a drill/driver equipped with a 5/16-inch nut-driver tip.

Attach the box to the joist with the two 1 1/2-inch No.

Set the box into the hole cut through the ceiling and press it tight against the underside of the joist.

(Be sure there's a cable connector attached to the knockout hole.)

Feed the electrical cable coming from the ceiling through the knockout hole in the pancake box.

Tip : Hold a vacuum cleaner wand next to the saw to catch the dust.

Hold a 1/2-inch-thick pancake box against the ceiling, centered on a joist, and trace around it with a pencil.

If it's suspended from a bar, you may have to take off a metal plate to unscrew the box then pry the bar from the joists.

#Wiring a ceiling fan with light and 4 wires from ceiling free#

If it's nailed to a joist, pry it free with a flat bar. Remove the old electrical box from the ceiling.Lower the fixture and disconnect the wires by twisting off the plastic connectors from the ends of the wires.

Unscrew the retaining nut or screws that hold the fixture to the ceiling.

Make sure electricity to circuit is turned off and carefully remove the glass shade or globe from the old light fixture.

#Wiring a ceiling fan with light and 4 wires from ceiling how to#

Ceiling Fan Overview Gregory Nemec How to Install a Ceiling Fan 1. Steer clear of hanging the fan too close to any lights, as rotating blades under a bulb will create an annoying flicker. High-cfm fans not only provide a better breeze, they usually have robust motors that will last longer and run more quietly.įor optimal performance, the fan should be hung at least 1 1/2 feet from the wall or a sloped ceiling, 7- to 10-feet from the floor, and at least 8 inches from the ceiling. Some 52-inch fans, for instance, rate as low as 2,050 cfm, while others reach 7,800. Make sure that the cubic feet of air that the fan moves per minute (cfm), measured at high speed, is near the top of its class. Larger living rooms and bedrooms can handle 50- to 54-inch blades. Spans of 36 to 42 inches work in rooms of up to 225 square feet, like a dining room. Step blade span down a bit for rooms with low ceilings, and go wider if the ceilings are high.Īnother good rule of thumb is to remember that blade spans of less than 36 inches are ideal for spaces smaller than 75 square feet, such as baths and breakfast nooks. Use this formula to find the best fan size for a room’s occupied space (the part of the room where people gather the most): Occupied space (in square feet) divided by 4 equals the blade span (in inches). Presuming you don’t have access to the ceiling fan from above, you must either use a specially rated hanger and box to mount the fan between joists or, better yet, screw a fan-rated “pancake” box (so called because it’s very thin) directly to a ceiling joist. It’s simply not strong enough to support the added weight and vibration of a fan. However-and this is very important-you can’t just hang the fan from the existing electrical box. The fan connects to the existing cable from the old light. The advantage of this approach is that you don't have to run new wiring. Here, we'll show how to replace an old light fixture with a new ceiling fan and light, in a room with no attic above. However, even when it isn't, the job is still quite doable.

Installing a ceiling fan is relatively simple, especially if the space above is accessible from an attic. In winter, they circulate heated air to keep the room warm. In summer, ceiling fans create cooling breezes, which reduce the strain on air conditioners. The popularity of ceiling fans continues to grow as more and more homeowners discover dramatic, year-round energy savings.